How to regrip your golf clubs at home

To regrip golf clubs at home, remove the old grip with a hooked blade, clean the shaft, wrap double-sided grip tape around the butt end, apply grip solvent inside the new grip and over the tape, then slide the new grip on in one smooth motion and align it before the solvent dries. Let the clubs dry upright for several hours, ideally overnight, before you play. Work in a ventilated area, protect the floor, and practise on one club first.

Golfer holding a club with a fresh grip on the course
Photo: Pexels

Know when a grip needs replacing

A grip needs replacing when it feels slick, hard or shiny, even after cleaning. Fresh grips have a tacky, textured feel that helps you hold the club without squeezing. As grips wear, that texture smooths out, and you start to grip tighter to compensate. Extra grip pressure reduces feel and can slow the swing, so worn grips affect more than comfort.

Check for cracks, splits and worn patches. Cracks often appear near the top of the grip or along the underside where the fingers rest. A split grip should be replaced promptly, since it can shift during a swing. Also check for a grip that has become smooth in one area but still feels tacky elsewhere, which usually means your hands wear one spot more than the rest. That pattern is normal, and it is a sign the grip has done its work.

Frequency depends on play and practice. A golfer who plays and practises regularly may need new grips every season, while an occasional player may go longer. Judge by feel and condition, not by calendar alone. If you notice yourself gripping tighter, or if cleaning no longer restores tackiness, it is time to regrip, even if the grips still look acceptable. Our guide to golf grip basics explains how grip pressure and hand placement affect the swing.

Gather the tools and materials

You need a small set of tools. A hooked grip removal blade or a sharp utility knife, double-sided grip tape, grip solvent, new grips in the correct size, a vice with a rubber shaft clamp, a tray or bucket to catch solvent, rags, and a cloth for the floor. A grip station or a simple vice setup holds the club steady, which makes every step easier and safer. Do not try to regrip with the club loose on a table, since it will move at the worst moment.

Choose grips that match your hand size and preference. Standard, midsize and oversize grips change the feel of the club and the amount of hand action in the swing. If you are unsure, replace one club first and test it before committing to a full set. Keep the same model across the set for consistency, unless you have a specific reason to vary one club. Consistency helps your hands feel the same on every club.

Work in a ventilated area, such as a garage with the door open, and protect the floor with old towels or a tray. Grip solvent has a strong smell and can damage some surfaces, so keep it away from painted floors and finished wood. Wear gloves if your skin is sensitive, and keep solvent away from open flames. A tidy workspace makes the job calmer and reduces mistakes.

Remove the old grip safely

Secure the club in the vice with the rubber clamp, so the shaft is held firmly without being crushed. Use the hooked blade to cut along the underside of the old grip, away from your body and away from your free hand. Work slowly, especially near the butt end, where the shaft is close to the blade. A steady, controlled cut is safer than a fast one, and it leaves a cleaner shaft for the new tape.

Peel the old grip off once it is cut, and pull the old tape off the shaft. If tape residue remains, use a small amount of solvent on a rag to soften it, then peel it away. Clean the shaft thoroughly, since leftover tape bumps can create lumps under the new grip. Check the shaft for damage while it is bare. Look for dents, cracks or rust near the butt end, and address any damage before fitting a new grip.

Dispose of old grips and tape carefully. Blades should go in a safe container, not loose in household waste. Keep the workspace clear between clubs, so offcuts do not end up underfoot. A clean start for each club helps you spot problems early, and it keeps the solvent and tape work consistent across the set.

Apply tape correctly

Wrap double-sided grip tape around the butt end of the shaft, starting just below the end cap area and working down for the length of the grip. Overlap each turn slightly, so no bare shaft shows through. Smooth the tape down firmly with your fingers, and press out air bubbles. A smooth tape layer gives a smooth grip, while wrinkles or gaps can be felt through the new grip.

Most golfers use one layer of tape for a standard feel. Extra layers build up grip thickness, which can help golfers with larger hands or those who prefer a thicker feel. If you add layers, add them evenly along the full length, not just in one spot, so the grip thickness stays consistent. Note how many layers you used on the first club, so you can repeat it exactly on the rest of the set.

Peel the backing off the tape only when you are ready to fit the new grip. The exposed adhesive is sticky and picks up dust quickly, which can weaken the bond. Keep the taped shaft clean and dry until solvent is applied. If you are regripping a full set, tape one club, fit its grip, and then move to the next club, rather than taping all shafts at once and leaving them exposed.

Fit the new grip with solvent

Pour a small amount of grip solvent into the new grip, cover the open end with your finger, and shake it to coat the inside. Then pour the solvent from the grip over the taped shaft, so both surfaces are wet. This lubrication lets the grip slide on smoothly. Work promptly, since solvent evaporates and the grip will start to grab as it dries. Do not use water as a substitute, since it does not activate the tape adhesive in the same way.

Slide the grip onto the shaft in one smooth, firm motion. Push it all the way to the butt end, without twisting it back and forth excessively. A single steady push gives the most even fit. If the grip stalls halfway, add a little more solvent and continue, rather than forcing it dry, which can tear the grip or bunch the tape underneath. Keep the club steady in the vice during this step.

Align the grip immediately, while it is still wet. Check that any logo, line or reminder rib sits in the position you want, usually square to the clubface or in your preferred alignment. Look down the shaft from the butt end to confirm the grip is straight, not rotated. Alignment is much harder to fix once the solvent dries, so take a few seconds to get it right now. A misaligned grip can subtly change your hand position on every shot with that club.

Let grips dry and check the fit

Stand the club upright with the grip end up, or lay it so the grip is not pressed against a surface, and let it dry for several hours. Overnight drying is the safest choice, especially for a full set. Do not play with a freshly gripped club the same day if you can avoid it, since a grip that is still drying can twist during a swing. Patience here protects all the work you just did.

Once dry, check each grip by hand. Twist it firmly to confirm it does not rotate on the shaft, and check that the butt end is flush and secure. Feel along the grip for lumps, tape edges or uneven thickness. A small lump usually means a tape wrinkle, and it is better to redo that grip now than to play with it for a season. A grip that feels smooth and secure is ready for the course.

Test the first regripped club at the range before regripping the whole set, if you changed grip size or model. Hit easy shots with irons and wedges, and notice whether the new size feels comfortable and whether your grip pressure stays relaxed. If the size feels wrong, you have only one club to change. If it feels right, continue with the rest of the set using the same tape layers and alignment.

Regrip a full set efficiently

Work through the set in order, from the longest iron to the shortest wedge, or in whatever order keeps your workspace tidy. Keep grips, tape and solvent within reach, and keep a rag handy for drips. A steady rhythm helps. Remove, clean, tape, solvent, fit, align, then set aside to dry. Repeating the same sequence builds speed and consistency, and it reduces the chance of skipping a step on a later club.

Label or note any variations. If one club needs an extra tape layer, or if you prefer a different alignment for a particular club, write it down. Memory fades over a long session, and a note prevents a full set of identical grips with one odd exception you did not intend. Keep the note with your golf gear, so the next regrip session starts from the same baseline.

Clean your clubs while you regrip, since the clubs are already out of the bag and in your hands. A clean clubface and clean grooves help performance, and the combined routine saves time later. Our guide to how to clean golf clubs covers a simple method that pairs well with regripping. Finishing both jobs together leaves your set ready for the next round.

Common regripping mistakes to avoid

The most common mistake is using too little solvent. A dry fit stalls halfway, tears the grip, or leaves tape bunched underneath. Use enough solvent to coat both surfaces generously, and keep a little extra nearby for a second application if needed. Solvent evaporates, so a generous first application is better than a cautious one that forces you to struggle.

A second mistake is rushing alignment. Golfers often slide the grip on and move straight to the next club, only to discover later that logos point in different directions. Alignment takes seconds while the grip is wet, and it affects hand position on every shot. Check alignment from the butt end, and also check it against the clubface, so the grip sits square as intended.

A third mistake is playing too soon. Fresh grips need time to bond fully. A grip that twists during a swing is not only annoying, it can also be unsafe if the club shifts in your hands. Wait until grips are fully dry, and test them with firm twists before play. If a grip moves at all, remove it and redo it, rather than hoping it will settle. A secure grip is worth the extra time, and it supports the relaxed grip pressure described in our guide to golf tension and relaxation.

Fresh grips, freer swing

New grips let you hold the club firmly without squeezing, which frees up your swing. Film your iron and wedge swings and check your grip and setup with FormCaddie.

Download FormCaddie free

More guides